A-110-2 Basic VCO |
|||||||
|
Das Modul A-110-2 ist ein preiswerter, spannungsgesteuerter Oszillator (engl. voltage-controlled oscillator). Es handelt sich um eine "abgespeckte" Version des Standard-VCOs A-110-1. Gegenüber dem A-110 fehlt der Sinus-Ausgang und statt des (teueren) Miniatur-Drehschalters ist ein 3-stufiger Oktav-Umschalter vorhanden. Dafür ist der A-110-2 gegenüber dem A-110-1 mit einem linearen FM-Eingang und einem Soft-Sync-Eingang ausgestattet. Mit Hilfe eines Jumpers kann der Bereich des Tune-Reglers zwischen ca. 1/2 Oktave und ca. 4 Oktaven gewählt werden. Gegenüber dem A-110-1 mit 10TE ist der A-110-2 nur 8 TE breit. Alle anderen technischen Daten sind im wesentlichen identisch zum A-110-1. Erläuterungen zu den Jumpern und Trimmpotentiometern:
Technische Hinweise: Der Sägezahnausgang des A-110-2 hat eine fallende (oder negative ) Flanke. Auf der Frontplatte ist irrtümlich eine steigende Flanke gezeichnet. Das hat zwar auf den Klang keine Auswirkung, bekommt jedoch eine Bedeutung wenn das Modul als LFO verwendet wird oder der Sägezahnausgang mit dem Sägezahnausgang eines anderen VCOs gemischt wird. Die 1V/Oct-Buchse an der Frontplatte wirkt additiv zu der Steuerspannung, die über den Bus zugeführt werden kann (abtrennbar über den Jumper JP2), d.h. die Bus-CV wird beim Einstecken eines Kabels in die Buchse 1V/Oct. nicht abgeschaltet ! Um auch ein Sinus-Signal zu erhalten, kann das Sinus-Konverter-Modul A-184-2 verwendet werden. Das Modul enthält zusätzlich eine spannungsgesteuerte Crossfader-Einheit, um zwischen zwei Kurvenformen spannungsgesteuert umblenden zu können. Das folgende Dokument zeigt die Positionen und Funktionen der Trimmpotentiometer und Steckbrücken: A110_2_trimming_potentiometers_and_jumpers.pdf |
||||||
|
|||||||
Module A-110-2 is a low-cost voltage-controlled oscillator. It's a slightly reduced version of the standard VCO A-110-1. Compared to the A-110-1 the A-110-2 has no sine output and the (expensive) octave rotary switch is replaced by a 3-position toggle switch. In return the A-110-2 is equipped with an additional linear FM input and a soft sync input. A jumper is used to select the range of the tune control between about 1/2 octave and about 4 octaves. The width of the module is only 8 HP compared to the 10 HP of the A-110-1. All other features are essentialy the same as for the A-110-1. Explanation of the jumpers and trimming potentiometers:
Technical remarks: The sawtooth output of the A-110-2 has a falling (or negative ) slope. The front panel shows erroneously a rising (or positive) slope. This has no influence to the sound but becomes important when the module is used as an LFO or is mixed with the sawtooth output of another VCO. The control voltage applied to the socket 1V/Oct is added to the control voltage coming from the bus (interruptible by removing the jumper JP2). Connecting a cable to the socket 1V/Oct does not interrupt the bus CV connection ! To obtain also a sine signal the triangle-to-sine converter module A-184-2 is recommended. It includes also a voltage controlled crossfader to fade between two waveforms. The following document shows the positions and functions of the jumpers and trimming potentiometers of the module: A110_2_trimming_potentiometers_and_jumpers.pdf |
|||||||
|
|||||||
Breite/Width:
8TE / 8HP / 40.3 mm Tiefe/Depth: 50 mm (gemessen ab der Rückseite der Frontplatte / measured from the rear side of the front panel) Strombedarf/Current: +12V: 150 mA (Aufheizperiode ca. 30 Sekunden / heat up period about 30 seconds), 60 mA (Dauerbetrieb / long-term current) -12V: 30mA |
|||||||
|
|||||||
Preise/Prices: Standard Version : Euro 135.00 Vintage Edition : Euro 150.00 The price in US$ depends upon the exchange rate between Euro and US$ at the payment day. |