Das MTC
Relay Board ist ein Erweiterungsplatine für die universell einsetzbare
MIDI-Steuerelektronik MTC64. Es verfügt
über sechzehn Reed-Relais, mit denen potentialfrei beliebige
Signale bis 100V/1A über MIDI-Noten- oder Programmwechsel-Befehle
geschaltet werden können (z.B. Audio-Signale, Lampen, Motoren,
Magnete, Leistungs-Relais usw.).
Hier die
wichtigsten Eigenschaften:
-
16
Reed-Relais, max. 100V, max. 1A, max 15 Watt pro Relais
-
Ansprechzeit
der Relais max. 2 Millisekunden
-
Relais-Anschlüsse
über 2-polige Schraubklemmen
-
maximal
4 der MTC Relay Boards können an eine MTC64-Basisplatine
angeschlossen werden
-
Die
Verbindung zwischen der bzw. den MTC Relay Boards und der
MTC64-Basisplatine erfolgt mit einem 10-poligen Flachbandkabel,
das von der Basisplatine zu allen Relay Boards führt, und jeweils
einem 16-poligen Flachbandkabel, das von der Basisplatine zu dem
jeweiligen Relay Board führt. Bitte geben Sie bei Ihrer
Bestellung an, wie viele Relay Boards mit der Basisplatine verbunden werden sollen (wegen der
Länge des 10-poligen Kabels und der Anzahl der aufgepressten
Steckverbindern)
-
Die
Flachbandkabel sind im Preis des Relay Boards enthalten.
-
Bei
der Verwendung älterer MTC64-Basisplatinen müssen ggf. die ICs vom Typ CD4094 gegen
74HC4094 ausgetauscht werden (gilt nur im Falle von Verwendung von
bereits vorhandenen, älteren MTC64-Basisplatinen aus der
Produktion vor 2005, bei Bestellung von MTC Relay Boards zusammen mit MTC64-Basisplatinen sind diese
natürlich bereits mit 74HC4094 ausgerüstet)
-
Der
Einbau und die Verdrahtung des MTC Relay Boards darf bei
Verwendung von Spannungen über 50 V nur von einem Fachmann durchgeführt
werden. Nicht
entsprechend ausgebildete Personen dürfen das MTC Relay Board
nur mit Spannungen unter 50V betreiben. Ansonsten besteht Lebensgefahr ! Vor Inbetriebnahme
muss die Einbau-Anleitung sorgfältig studiert und alle Hinweise
genau beachtet werden. Der gesamte Aufbau
berührungssicher in ein Gehäuse eingebaut werden.
-
Abmessungen:
163 x 52 x 18 mm
-
Preis:
80.00 Euro, incl. 16-poligen Verbindungskabel
zur MTC-Hauptplatine, ohne sonstiges
Kabelmaterial
Produktion eingestellt, nicht mehr lieferbar
-
Zur näheren Information steht die Einbau-
und Bedienungsanleitung als pdf-Datei zur Verfügung: MTC_Relay_Anleitung.pdf
|
The MTC
Relay Board is an expansion board for the universal MIDI control electronics MTC64.
It can be used to switch any signal (AC or DC) up to 100V/1A by means of
Reed relays (for example audio signals, lamps, motors, magnets, power
relays). The relays are controlled by MIDI
note on/off or program change messages.
These are the
most important features:
-
16 Reed
relays, max. 100V, max. 1A, max. 15 W (each relay)
-
response
time of the relays less than 2 milliseconds
-
relay connections via screw terminals
-
up to four
MTC relay boards can be connected to one MTC64 main board
-
connection
between MTC relay boards and MTC64 main board via one 10 pin ribbon
cable leading from the main board to all relay boards, and a 16 pin
ribbon cable between main board and relay board (one for each relay board). Please specify
in your order how many relay boards have to be connected to
the main board (because of the lenght and number of female connectors
of the 10 pin ribbon cable)
-
the ribbon
cables are included with the relay board
-
On the
MTC64 main board the integrated circuits labelled CD4094 have to be
replaced by 74HC4094 (valid only if an already existing older main board
manufactured before 2005 is
used, in case of new orders of main boards in combination with relay boards the main boards are already equipped with 74HC4094)
-
Installation
and wiring of the MTC relay board has to be carried out by qualified personnel only
if voltages beyong 50V are used. Not qualified personell is
not allowed to install and run the MTC relay board with voltages
beyond 50V! DANGER TO
LIFE ! The user has to read the installation manual carefully and
follow all instructions in the manual meticulously !
The complete construction has to be mounted into an isolating case.
-
dimensions:
163 x 52 x 18 mm
-
price: Euro 80.00, including 16 pin ribbon
cable to CTM main board, without other cables
no
longer available
-
The prices in US$
depend upon the exchange rate between Euro and US$ at the payment day.
Free currency converter:
-
For more
detailed information the user's manual is available on our web site as
pdf file:
MTC_relay_manual.pdf
|