nicht mehr verwenden ! 

Stattdessen nur noch A-100 DIY Kits benutzen !

 

A-100 DIY Kit #1

 

zur Vergrößerung das Bild anklicken / click to enlarge
 

Der A-100 Do-it-yourself-Kit 1 ist eine Zusammenstellung von Komponenten, die den preiswerten Eigenbau eines Gehäuses für das A-100-System erlaubt:

  • Netzteil mit externem Trafo (aus Gründen der elektrischen Sicherheit, keine lebensgefährlichen Netzspannungen)

  • maximaler Strom: 1200mA (wie PSU2, jedoch kein Ringkerntrafo sondern externer Trafo)

  • 2 Busplatinen

  • 4 Gewindeschienen 84TE zur Montage der A-100-Module (abgewinkelter Metallstreifen mit Innengewinden im 2 TE-Abstand, siehe untenstehenden Hinweis), ausreichend für ein 2x3HE-Gehäuse -> Änderung ab April/Mai 2008, siehe untenstehenden Hinweis 4

  • Kabelmaterial zur Verbindung von Netzteil und Busplatinen

  • Maßskizzen zu Busplatinen und Netzteil (zum Bohren der passenden Löcher)

  • Bauvorschlag für Holzgehäuse (Skizze + Liste der benötigten Holzplatten)

  • zusätzliches Montagematerial wie etwa Schrauben, Muttern oder Abstandsbolzen (für Busplatinen, Netzteil, Gewindeschienen etc.) ist nicht enthalten, da hier je nach Typ des Gehäuses unterschiedliche Teile erforderlich sind

  • Preis: 120,00 Euro (kompletter Satz)

  • nur Netzteil mit Trafo: 60,00 Euro (ohne Busplatinen, ohne Gewindeschienen, ohne Buskabel)

  • nur Netzteil ohne Trafo: 40,00 Euro, es wird ein externer Trafo mit 15V (Wechselspannung) und dem doppelten Wert des gewünschten Stroms benötigt, maximal 2x1200mA = 2,4A, auch kleinere Stromabgabe möglich (bei einem Trafo mit 15V/1A~ wären dies beispielsweise 500mA)

  • Die Unterlagen zum A-100 DIY Kit 1 sind als pdf-Datei verfügbar.

  • Hinweis 1: Da der Abstand der Innengewinde 2 TE beträgt können nur A-100-Frontplatten komplett montiert werden (d.h. alle Schrauben), die mit nur zwei Montageschrauben befestigt werden. Für Frontplatten mit 4 Montageschrauben sind die Gewindeschienen nicht geeignet, da hier der Abstand zwischen den Löchern ein ungeradzahliges TE-Vielfaches ist. Wir sind gerade dabei auch Gewindeschienen mit 1TE Abstand fertigen zu lassen, damit alle Arten von Frontplatten montiert werden können.

  • Hinweis 2: Falls die Version ohne Steckertrafo zum Einsatz kommt, muss aus Gründen der elektrischen Sicherheit unbedingt ein berührungssicher gekapselter Trafo verwendet werden (15V AC, max. 2400 mA). Die Verwendung von offenen Trafos, die vom Anwender noch über Kabel mit dem Netz verbunden werden müssen, ist nicht erlaubt, da hier der Vorteil der elektrischen Sicherheit des DIY-Kits wieder zunichte gemacht wird. Es kann auch ein Trafo mit einem Strom kleiner als 2400mA eingesetzt werden, sofern der Strombedarf der Module kleiner als der halbe Strom des verwendeten Trafos ist (Beispiel: Trafo-Strom = 1A -> 500 mA Strom für die A-100-Module).

  • Hinweis 3: Falls die Version ohne Netzteile zum Einsatz kommt, müssen aus Gründen der elektrischen Sicherheit unbedingt berührungssicher gekapselte Steckernetzteile verwendet werden (12V, Gleichspannung, stabilisiert, max. 500mA, Polarität: Außenring = Masse, Innen = +12V). Die Verwendung von offenen Netzteilen, die vom Anwender noch über Kabel mit dem Netz verbunden werden müssen, ist nicht erlaubt, da hier der Vorteil der elektrischen Sicherheit des DIY-Kits wieder zunichte gemacht wird. Es können auch Netzteile mit einem Strom kleiner als 500mA eingesetzt werden, sofern der Strombedarf der Module kleiner als der maximale Strom der verwendeten Netzteile ist.

  • Hinweis 4: Ab April/Mai 2008 werden die DIY-Kits auf reguläre Profilschienen umgestellt (wie bei den normalen A-100-Rahmen und Koffern verwendet). In die Profilschienen werden jedoch aus Kostengründen normale M3-Muttern eingeschoben (keine Gewindestreifen).

 

The A-100 DIY kit #1 is a combination of components that allows the inexpensive do-it-yourself construction of a case for the A-100:

  • power supply with external transformer (AC output)

  • because of safety reasons, no dangerous voltages accessible

  • max. current: 1200mA (same as PSU2, but external transformer instead of ring core transformer)

  • 2 bus boards

  • four 84 HP mounting rails with threaded inserts (distance between the threads = 2 HP, see remark below) for module mounting (sufficient for 2x3U) -> revision from April/May 2008, see remark #4

  • cable for connections between power supply and bus boards

  • sketches with measures (for drilling the holes at the right positions for PSU and bus board mounting)

  • building suggestion for wooden case (sketch + list of all required wooden case parts)

  • additional installation material like screws, nuts or distant bolts (e.g. for bus boards, power supply board, rails) is not included as these parts depend upon the type of case built by the customer

  • Price: Euro 120.00 (complete kit with transformer), Euro 100.00 (complete kit without transformer)

  • power supply only (with transformer): Euro 60.00 (without bus boards, without mounting rails, without bus cables)

  • power supply only (without transformer): Euro 40.00

  • transformer only: Euro 20.00

  • attention: from Doepfer (Germany) only 230V transformers with European mains plug type are available (external transformer with 15V/2.5A AC required), please ask the Doepfer representative in your country if they have a transformer available that is suitable for the mains voltage and mains plug in your country

  • even smaller current output is possible; the current output of the power supply is half the current of the external transformer as the currents for both voltages +/-12V are required (if e.g. the transformer outputs max. 1000mA the max. power supply current is 500mA) 

  • the technical documents are available as pdf file

  • Remark # 1: As the thread distance is 2 HP only A-100 modules with two mounting holes can be mounted completely (i.e. all mounting screws). The threaded rails cannot be used for complete mounting of panels with 4 mounting holes as the distance between the holes is an odd HP multiple for these panels. We already asked our manufacturer to produce even rails with 1 HP thread distance and we hope that we will be able to offer these rails soon so that all types of panels can be mounted.

  • Remark # 2: If the version without transformer is used: Because of electrical safety only an encapsulated transformer is allowed (15V AC, max. 2400 mA). Open transformers that have to be wired to the mains by the user are not allowed ! This would nullify the safety advantages of the DIY kit. Even a transformer with less than 2400mA can be used provided that the total current of the modules is less than half the current of the transformer (example: transformer current = 1000 mA -> 500 mA available for the modules).

  • Remark # 3: If the version without power supplies is used: Because of electrical safety only encapsulated wall outlet power supplies are allowed (12V DC, stabilized, max. 500 mA, polarity: ring = GND, center = +12V). Open frame supplies that have to be wired to the mains by the user are not allowed ! This would nullify the safety advantages of the DIY kits. Even supplies with currents less than 500mA can be used provided that the total current of the modules is less than the max. current of the supplies.

  • Remark # 4: From about April/May 2008 the contents of the DIY kits will change to normal front rails (same as used in the standard A-100 frames and suitcases) instead of the mounting rails with threads mentioned above. To keep the costs as low as possible normal M3 nuts are slided into the rails (not threaded inserts as used in the standard A-100 frames and suitcases).