A-100 Future Modules
(as of February 2019)

The following modules are no longer available:

and all modules with blue LEDs (sale while stocks last without additional charges)


The modules in the list below are still in the planning or development stage. For all these modules we have no additional information available so far (delivery date, price, detailed features and so on). Please refrain from asking for these information. As soon as more detailed features, prices and dates of delivery are available you will find them here on our web site. At present we are about to plan the following modules. Information is still without obligation !
Previous notice: A-197-3 RGB LED Controller

planned for end of February 2019, price ~ Euro 80.00, incl. free 1m RGB LED stripe, price and release date are still without obligation !

already available

Previous notice: A-135-2 Quad VCA / Voltage Controller Mixer

planned for end of 2018, price ~ Euro 120.00, price and release date are still without obligation !

already available

Previous notice: A-180-4 Quad Buffer/ Buffered Multiple II

planned for end of 2018, price ~ Euro 50.00, price and release date are still without obligation !

already available

Previous notice: A-190-5 four voice polyphonic Midi to CV/Gate interface with 12 CV and 4 Gate outputs, different modes (e.g. unisono, four-fold monophonic, different four voice polyphonic modes)

planned for end of 2018, price ~ Euro 300.00, price and release date are still without obligation !

already available

Previous notice: A-183-9 Quad USB Supply

planned for November 2018, price ~ Euro 50,00, price and release date are still without obligation !

already available

Previous notice: A-123-2 6/12/18/24dB Hochpass

planned for October 2018, price ~ Euro 120,00, price and release date are still without obligation !

already available

Previous notice: A-105-4 polyphonic 24dB Lowpass (SSM version)

planned for September 2018, price ~ Euro 200,00, price and release date are still without obligation !

already available

Previous notice: A-142-2 Dual Envelope Controlled VCA

planned for August 2018, price ~ Euro 150,00, price and release date are still without obligation !

already available

Previous notice: A-140-2 Dual Miniature ADSR

planned for Juli 2018, price ~ Euro 140,00, price and release date are still without obligation !

already available

Previous notice: A-132-8 polyphonic Octal-VCA

planned for June 2018, price ~ Euro 160,00, price and release date are still without obligation !

already available

Previous notice: A-141-4 polyphonic VCADSR

planned for May 2018, price ~ Euro 160,00, price and release date are still without obligation !

already available

Previous notice: A-180-9 Multicore

planned for April 2018, price ~ Euro 120,00 (module pair with cables), price and release date are still without obligation !

already available

Previous notice: A-111-4 Quad VCO 

planned for October 2017, price ~ Euro 400,00, price and release date are still without obligation !

already available

Previous notice: A-150-8 Octal Voltage Controlled Switch

planned for October 2017, price ~ Euro 150,00, price and release date are still without obligation !

already available

Previous notice: A-173-1/2 Micro Keyboard / Manual Gates

planned for October 2017, price ~ Euro 180,00 Euro, price and release date are still without obligation !

already available

Previous notice: A-100LMS9 und A-100LMB

low cost versions of the A-100 Monster Cases A-100PMS9 and A-100PMB
optionally made of raw wood or black coated (appendix "V")


planned for October 2017, Prices: Price list / chapter A-100 cases, price and release date are still without obligation
!

already available

Previous notice: A-138s Mini Stereo Mixer

planned for August 2017, Price ~ Euro 75,00,  price and release date are still without obligation !

already available

Previous notice: A-135-4 A/B/C Voltage Controlled Performance Mixer Modules

planned for July 2017, price and release date are still without obligation !

already available

Previous notice: A-110-6 Trapezoid Thru Zero Quadrature VCO

planned for June 2017, Price ~ Euro 250,00,  price and release date are still without obligation !

already available

Previous notice: A-100LC1 48 HP low cost case with built in power supply A-100SSB (+12V/380 mA, -12V/380mA)

planned for May 2017, price and release date are still without obligation !

already available

Previous notice: A-111-2 High End VCO II

planned for November 2016, price ~ Euro 250.00, price and release date are still without obligation !

already available

 

Previous notice: A-111-3 Micro Precision VCO/VCLFO

planned for October 2016, price ~ Euro 160.00, price and release date are still without obligation !

already available

Previous notice: A-138p/o Performance Mixer Modules

planned for September 2016
price A-138o: ~ Euro 50.00
price A-138p: ~ Euro 110.00
prices and release dates are still without obligation
!

already available

Previous notice: A-184-2 Sine Converter / Voltage Controlled Crossfader

planned for September 2016, price ~ Euro 80.00 Euro, price and release date are still without obligation !

already available

Previous notice: A-100 SSB Small Supply/Bus, small power supply and bus board with 8 bus connectors, 100-240V mains voltage

planned for August 2016, price ~ Euro 75.00, price and release date are still without obligation !

already available

Previous notice: Amplifier option for the first version of A-110-4 Thru Zero Quadrature VCO
(increases the levels of both outputs)

planned for July 2016, price ~ Euro 25.00 Euro, price and release date are still without obligation !

already available

Previous notice: A-121-2 12dB Multimode Filter

planned for June 2016, price ~Euro 120,00, price and release date are still without obligation !

already available


? Previous notice: A-126-2 Frequency Shifter (redesign of A-126)
? Previous notice: A-149-3 Fluctuating Random Voltages,  no release date so far 
the example shown on the patch example page will be available as a separate module
? Previous notice: A-149-4 Chaos Module. The example shown on the patch example page is planned as a separate module. No planned release date so far.
? Previous notice: A-195-1 Pitch-to-CV/MIDI Interface (?): interface for conversion of a monophonic audio signal (e.g. singing, wind or string instrument) into the corresponding pitch CV (1V/Oct.), loudness CV and gate. Simultaneously the values are transmitted via MIDI. No release date so far.

Previous notice: Touch Sensor Keyboard
The following link leads to the preliminary information about the A-100 keyboard project: A-100 Keyboard/Sequencer project
no release date so far 
This project has been cancelled

Previous notice: 30/60dB Switched Capacitor Filter,  no release date so far 

This project has been cancelled

Previous notice: Clocked Audio Delay,  no release date so far 

This project has been cancelled

?

Previous notice: A-143-6 Multiple Synced VC LFO. This link leads to a provisional information about the planned module. No planned release date so far.

This project has been cancelled

?

Previous notice: Dual balanced VCF. This link leads to a provisional information about the planned module. No planned release date so far.

This project has been cancelled


For all modules listed above we have no additional information available so far. Please refrain from asking for more details - especially via email. As soon as detailed features, prices and dates of delivery are available you will find them here on our internet pages as particular pages in the A-100 modules overview.
 

A-100 New Modules (already available)
(as of September 2017)

Previous notice: A-110-2, low cost basic VCO, similar to A-110, waveforms: sawtooth, triangle and rectangle with PWM, 3-position octave switch (instead of the rotary switch of A-110), Hard Sync input, Soft Sync input, linear FM input, 8 HP front panel

already available

Previous notice: A-101-6, six stage Opto-FET VCF

already available

Previous notice: A-147-2, voltage controlled LFO (VCLFO) with extensive control possibilities, e.g. VCA for output level, Delay CV for delayed LFO

already available

Previous notice: A-138u,  simple, low-cost mixer with two units. Each unit is equipped with 3 inputs and one output. The upper unit has for each input a trimming

already available

Previous notice: A-160-2, enhanced clock divider, similar to A-160, but with much more features like integer, prime and power of two dividing factors, gate and trigger mode, polarity of clock and reset selectable, normal/inverted outputs, 4 HP front panel

already available

Previous notice: A-160-5, clock multiplier/ratcheting controller

already available

Previous notice: A-139-2, headphone amplifier

already available

Previous notice: A-110-4 Thru-Zero Quadrature VCO

already available

Previous notice: A-180-3, dual buffered 1-in-3 Multiple

already available

Previous notice: A-157 Trigger sequencer  with 8 tracks, 16 steps each, button/LED matrix with 8x16 momentary switches and LEDs, 32 function buttons/LEDs, 8 trigger outputs with display, input unit with 8 inputs and buttons for Start, Stop, Reset, Clock and 4 free assignable functions
planned for early 2016
a stand-alone version (Dark Flow) is also in the planning stage 
price and release date are still without obligation
!

already available

Previous notice: A168-1, PW/PWM-Generator

planned for early 2016, price ~ Euro 50.00, price and release date are still without obligation !

already available

Previous notice: A-184-1 Ring Modulator / S&H/T&H / Slew Limiter Combo

planned for May 2016, price ~ Euro 100.00, price and release date are still without obligation !

already available

Previous notice: A-110-2, low cost basic VCO, similar to A-110, waveforms: sawtooth, triangle and rectangle with PWM, 3-position octave switch (instead of the rotary switch of A-110), Hard Sync input, Soft Sync input, linear FM input, 8 HP front panel

already available

Previous notice: A-101-6, six stage Opto-FET VCF

already available

Previous notice: A-147-2, voltage controlled LFO (VCLFO) with extensive control possibilities, e.g. VCA for output level, Delay CV for delayed LFO

already available

Previous notice: A-138u,  simple, low-cost mixer with two units. Each unit is equipped with 3 inputs and one output. The upper unit has for each input a trimming

already available

Previous notice: A-160-2, enhanced clock divider, similar to A-160, but with much more features like integer, prime and power of two dividing factors, gate and trigger mode, polarity of clock and reset selectable, normal/inverted outputs, 4 HP front panel

already available

Previous notice: A-160-5, clock multiplier/ratcheting controller

already available

Previous notice: A-139-2, headphone amplifier

already available

Previous notice: A-110-4 Thru-Zero Quadrature VCO

already available

Previous notice: A-127BOM, breakout module for the triple filter module A-127, features separate access to each of the three filters of the A-127, separate outputs lowpass, highpass, bandpass and notch for each filter, separate audio input for each filter, 8 HP front panel

already available

Previous notice: A-190-4 USB/Midi to CV/Gate/Sync Interface (replacemen for A-190-1)

already available

Probably from early 2014 the "small brother" of the monster base A-100PMB will be available. The new case A-100PB is very similar to the A-100PMB but has only half the width (2 x 84 HP for installation of modules). The suitcase versions A-100P6 or A-100P9 can be positioned on top of the A-100PB because the width of the A-100PB is a bit more than the width of A-100P6/P9 and the footprint of the A-100PB is adapted to the depth of A-100P6/P9. A-100PB is equipped with one power supply (1200mA) and two bus boards. The bus boards are located in the rear area (even those for the modules that are mounted in the front row). This was necessary to take advantage of the full height of the front area for installation of A-100 modules. The max. depth for modules in the front row is ~70 mm. The outside dimensions in mm are about  510 (width) x 420 (depth) x 210 (height).  The price of the A-100PB will be about Euro 550 (without modules).

already available

Probably from early 2014 the "small brother" of the low cost case A-100LC6 will be available. The A-100LC3 is very similar to the A-100LC6 but offers only one row with 84 HP for installation of modules. A-100LC3 is equipped with one power supply (1200mA) and one bus board. Because of the limited space the power suppy of the DIY-Kit #1 with an external transformer is used (same as for the DIY-Kit #1). At the left side of the case the connector for the external transformer is located. The external transformer is not shown in the above pictures. The outside dimensions in mm are about  445 (width) x 160 (depth) x 150 (height). The price of the A-100LC3 will be about Euro 180-200 (including external power supply for 230 or 115V AC, without modules).

already available

Previous notice: A-192-2 Dual CV/Gate-to-MIDI/USB Interface: interface for conversion of several CV and gate signals into the corresponding midi note messages, at the rising edge of the gate the CV voltage is measured and a corresponding note on message is generated, at the falling edge of the gate signal the corresponding note off message is generated, two additional voltages can be are converted into midi messages too (e.g. velocity, volume, free assignale controller)

already available

Previous notice: A-180-2 Small version of the multiple module A-180

already available

Previous notice: A-171-2 Voltage Controlled Slew Limiter II (Serge/VCS clone)

already available

Previous notice: A-141-2 Voltage Controlled ADSR/LFO

already available

Previous notice:A-190-8  Midi/USB-to-Sync Interface

already available

Previous notice: A-192-2 Dual CV/Gate-to-MIDI/USB Interface: interface for conversion of several CV and gate signals into the corresponding midi note messages, at the rising edge of the gate the CV voltage is measured and a corresponding note on message is generated, at the falling edge of the gate signal the corresponding note off message is generated, two additional voltages can be are converted into midi messages too (e.g. velocity, volume, free assignale controller)

already available

Previous notice: A-180-2 Small version of the multiple module A-180

already available

Previous notice: A-190-3 USB/Midi to CV/Gate Interface, modular version of Dark Link, Euro 120.00

already available

Previous notice: A-142-4 Quad envelope generator (decay only), Euro 100.00

already available

Previous notice: A-143-4 Quad VCLFO/VCO, four-fold voltage controlled LFO/VCO,  Euro 220.00

already available

Previous notice:A-132-4 Quad exponential VCA/Mixer, planned for May 2010, price ~ Euro 100.00, price and release date are without obligation

already available

Previous notice: A-177-2, simple, economically priced interface module for foot switches and foot controller, similar to A-177 but without LEDs and controls, planned for end of 2009, price ~ Euro 40, price and release date are without obligation

already available

Previous notice: A-174-2 Wheels Module, simple modulation wheel module with 2 black wheels

already available

Previous notice: A-187-1 Voltage Controlled DSP Effects Module, a DSP based effects module with voltage control of four parameters of the selected digital effect

already available


new A-100 monster case with 2 x 9U (angled version), planned for fall 2009

already available

Previous notice: A-138m Matrix Mixer planned for summer 2009, price ~ Euro 120, price and release date are still without obligation

already available

Previous notice: A-183-1 Dual Attenuator, planned for summer 2009, price ~ Euro 30-35 Euro, price and release date are still without obligation

already available

Previous notice: A-183-2 Offset Generator/Attenuator/Polarizer, planned for summer 2009, price ~ Euro 35-40 Euro, price and release date are still without obligation

already available

Previous notice: A-183-3 Amplifer 1/2/4-fold, planned for summer 2009, price ~ Euro 35-40 Euro, price and release date are still without obligation

already available

Previous notice: Monster Base Frame

already available

Previous notice: A-132-3 Dual linear/exponential VCA

already available

Previous notice:A-106-6 XP VCF with 15 different filter types

already available

Previous notice: A-134-2 Dual Voltage Controlled Crossfader (4 HP module)

already available

Previous notice: A-137-2 Wave Multiplier II

already available

Previous notice: A-138e Quad Three-Way Crossfader / Mixer / Polarizer

already available

Previous notice: A-189-1 Voltage Controlled Bit Cruncher / Modifier

already available

Previous notice: A-190-2 economically priced Midi-to-CV/Gate interface (modular version of the MCV4), 4 CV outputs: CV1 = note, CV2 = pitch-bend, CV3 = volume/velocity, CV4 = assignable midi controller

already available

Previous noticeA-138d Crossfader/FX insert

already available

Previous notice: A-164-1 Manual Gate

already available

Previous notice: A-182 Switched Multiple

already available

Previous notice:A-185-2 Precision Adder/Bus Access

already available

Previous notice: A-186-1 Gate/Trigger Combiner

already available

Previous notice: A-100 Do-it-yourself-Kit #2

already available

Previous notice: A-106-5, SEM VCF

already available

Previous notice: A-132-2, Quad VCA

already available

Previous notice: A-143-9 Voltage Controlled Quadrature LFO/VCO

already available

Tapped BBD module A-188-2. This link leads to the information about the new module

already available

BBD module A-188-1. This link leads to the information about the new module

already available

Universal Vactrol Module A-101-9. This link leads to the information about the new module

already available

A-100 Power Supply 2 (A-100PSU 2): New power supply with more power (1200mA) and ring core transformer for less mechanical hum and less electrical hum radiation

already available

A-106 Xtreme Filter (MS20 Low/High Pass). This link leads to the information about the new module

already available

A-151 Quad Sequential Switch (version 2). This link leads to the information about the revised module

already available

A-143-1 Complex Envelope Generator (Quad AD Generator/LFO). This link leads to the information about the module

already available

A-143-2 Quad ADSR. This link leads to the information about the module

already available

A-143-3 Quad LFO. This link leads to the information about the module

already available

A-101-1 Vactrol Steiner Multimode Filter. This link leads to the information about the new module

already available

Vactrol Basics

A-101-2 Vactrol Low Pass Gate. This link leads to the information about the new module

already available

Vactrol Basics

A-152 Voltage Addressed S&H/Switch. This link leads to the information about the new module

already available

A-138c Polarizing Mixer. This link leads to the information about the new module

already available

A-101-3 Modular 12 Stage Vactrol Phaser. This link leads to the information about the new vactrol phaser module

already available

Vactrol Basics

A-154 Sequencer Controller. This link leads to the information about the new enhanced sequencer controller. The A-154 adds a lot of new features to the Analog/Trigger Sequencer A-155, e.d. different running modes (forward, backward, pendulum, random and voltage controlled step addressing), parallel/serial operation of two or more A-155, voltage controlled clock generator with voltage controlled gate length, and many more....)

already available

A137 Front Panel A-137 Wave Multiplier. This link leads to the information about the new Wave Multiplier module

already available

A-149-2 Digital Random Voltages. This link leads to the information about the new random digital voltages module (extension for A-149-1)

already available

Redesign A-138a/b. From April 2004 an improved version of the module A-138b is manufactured. For the revised version control Input 1 works as a DC offset generator (about 0...+5V) provided that no patch cord is plugged into socket In1. If this feature is not required it can be deactivated by removing a jumper on the pc board. Probably from summer 2004 even the A-138a will be manufactured with this improvement

already available

Redesign A-150. From May 2004 an improved version of the module is manufactured. The revised version allows to process voltages in the full A-100 voltage range (i.e. -12V....+12V). The previous limitation to -8...+8V is no longer valid. The new version can be distinguished from the previous version by the printing at the pcb ("A-150 DUAL VC SWITCH VERSION 2"). Another way to distinguish the two versions are the integrated circuits: "CD4053" for the old version, "DG409" for the new version. Sorry it is not possible to update the old version of the A-150 to the new one as the complete circuit has been changed

already available

A-107 Multitype Morphing Filter. This is a brand new Multitype Morphing Filter. This module contains completely new features that - as far as we know - are available for none of the other filters on the market: Probably more than 30 different filter types are available (different types of low pass, high pass, band pass, notch, all pass and completely new combined filter types) that can be passed through with a control voltage. Even the morphing time (i.e. how fast the next filter type comes up) is voltage controlled. The provisional A-107 page shows the most important features of the module and the filter response curves of the filters that are included so far.

already available

A102 Front Panel A-133 Voltage Controlled Polarizer. This link leads to a provisional information about the special dual voltage controlled amplifier that enables both positive and negative amplifications. Negative amplifications means in this context that the signal is inverted. The main application of the module is the processing of control voltages, e.g. ADSR or LFO. The amplification range will be (prospectively)  -5....0....+5. Amplification can be adjusted manually or by an external control voltage. The current amplification is displayed with two LEDs: one for positive and one for negative amplifications.

already available

A102 Front Panel A-149-1 Source of Uncertainty (1). This link leads to a provisional information about the first module of the A-149-x range. In this group we present by popular request several functions of Don Buchla's "Source of Uncertainty 265/266" (SOU) modules that cannot be realized with existing A-100 modules. Many functions of Buchla's 265 and 266 SOU can be realized with existing A-100 modules. For details please refer to A-100 patch examples. Module A-149-1 has available four different analog random control voltages that are generated in different ways.

already available

A102 Front Panel A-167 Analog Comparator / Subtractor / Offset Generator. This link leads to a provisional information about the analog comparator that can be used as voltage subtractor and offset generator too.

already available

A102 Front Panel A-172 Minimum/Maximum Selector. This link leads to a provisional information about the minimum/maximum selector module that is equipped with four analog inputs and two analog outputs (minimum, maximum). The main application of the module is the processing/mixing of control voltages, e.g. random voltages, ADSR, LFO, S&H, ribbon CV, theremin-CV and similar. The module permanently picks the maximum resp. minimum voltage out of the four input signals and outputs these voltages to the maximum resp. minimum jack socket.

already available

A102 Front Panel A-196 PLL. This link leads to a provisional information about the phase locked loop module. The module can be used for frequency multiplication or special sound effects.

already available