A-100 A-100 DIY Kit #2

 

zur Vergrößerung das Bild anklicken / click to enlarge
 

Der A-100 Do-it-yourself-Kit 2 ist eine Zusammenstellung von Komponenten, die den sehr preiswerten Eigenbau eines 3HE-Gehäuses für das A-100-System erlaubt:

  • extrem preiswertes Einsteigerpaket zur Verwendung mit externen 12V-Steckernetzteilen (nicht für hochwertige Anwendungen empfohlen)

  • aus Gründen der elektrischen Sicherheit, keine lebensgefährlichen Netzspannungen

  • maximaler Strom: 500mA

  • 1 Busplatine

  • 2 Gewindeschienen 84TE zur Montage der A-100-Module (abgewinkelter Metallstreifen mit Innengewinden im 2 TE-Abstand, siehe untenstehenden Hinweis 2), ausreichend für ein 3HE-Gehäuse -> Änderung ab April/Mai 2008, siehe untenstehenden Hinweis 4

  • 2 Steckernetzteile 12V/500mA (stabilisierte Schaltnetzteile mit Weitbereichseingang 100 ... 240 VAC)

  • Kabelmaterial und Adapterplatine zur Verbindung der Netzteile und der Busplatine

  • Bauvorschlag für Holzgehäuse (Skizze + Liste der benötigten Holzplatten)

  • zusätzliches Montagematerial wie etwa Schrauben, Muttern oder Abstandsbolzen (für Busplatine, Adapterplatine, Gewindeschienen etc.) ist nicht enthalten, da hier je nach Typ des Gehäuses unterschiedliche Teile erforderlich sind

  • Preise:

  • 60,00 Euro (kompletter Satz)

  • 50,00 Euro (kompletter Satz ohne Netzteile, zwei stabilisierte 12V-Netzteile mit dem gewünschten Maximalstrom erforderlich)

  • Die Unterlagen zu den A-100 DIY Kits sind als pdf-Datei verfügbar.

  • Hinweis 1: Diese sehr preiswerte Art der Stromversorgung ist nicht mit der Qualität des regulären A-100-Netzteils (A-100PSU2) vergleichbar. Daher sollte der A-100 DIY Kit 2 nur für den ersten Einstieg oder für einfache Anwendungen (speziell: ohne VCOs) eingesetzt werden. Die Spannungsstabilität reicht nicht annähernd an die des regulären A-100-Netzteils (A-100PSU2) heran. Speziell bei der Verwendung von VCOs kann es zu Tuning-Problemen kommen. Die Busplatine und die Gewindeschienen (die den größten Kostenanteil an dem DIY Kit 1 haben) können aber auch später beim Einsatz eines hochwertigen Netzteils (z.B. A-100 PUS2 oder A-100 DIY Kit 1) weiter verwendet werden. Im Zweifelsfall raten wir zum A-100 DIY Kit 1, da hier eine wesentlich hochwertigere Stromversorgung zum Einsatz kommt.

  • Hinweis 2: Da der Abstand der Innengewinde 2 TE beträgt können nur A-100-Frontplatten komplett montiert werden (d.h. alle Schrauben), die mit nur zwei Montageschrauben befestigt werden. Für Frontplatten mit 4 Montageschrauben sind die Gewindeschienen nicht geeignet, da hier der Abstand zwischen den Löchern ein ungeradzahliges TE-Vielfaches ist. Wir sind gerade dabei auch Gewindeschienen mit 1TE Abstand fertigen zu lassen, damit alle Arten von Frontplatten montiert werden können.

  • Hinweis 3: Falls die Version ohne Netzteile zum Einsatz kommt, müssen aus Gründen der elektrischen Sicherheit unbedingt berührungssicher gekapselte Steckernetzteile verwendet werden (12V, Gleichspannung, stabilisiert, max. 500mA, Polarität: Außenring = Masse, Innen = +12V). Die Verwendung von offenen Netzteilen, die vom Anwender noch über Kabel mit dem Netz verbunden werden müssen, ist nicht erlaubt, da hier der Vorteil der elektrischen Sicherheit des DIY-Kits wieder zunichte gemacht wird. Es können auch Netzteile mit einem Strom kleiner als 500mA eingesetzt werden, sofern der Strombedarf der Module kleiner als der maximale Strom der verwendeten Netzteile ist.

  • Hinweis 4: Ab April/Mai 2008 werden die DIY-Kits auf reguläre Profilschienen umgestellt (wie bei den normalen A-100-Rahmen und Koffern verwendet). In die Profilschienen werden jedoch aus Kostengründen normale M3-Muttern eingeschoben (keine Gewindestreifen).

The A-100 DIY kit #2 is a combination of components that allows the very inexpensive do-it-yourself construction of a 3HE case for the A-100:

  • extremely low cost beginners package for usage in combination with two external 12V wall-outlet power supplies (not recommended for high quality applications)

  • because of safety reasons, no dangerous voltages accessible

  • max. current: 500mA

  • one bus board

  • two 84 HP mounting rails with threads (distance between the threads = 2 HP, see remark # 2 below) for module mounting (sufficient for one 3 U case) -> revision from April/May 2008, see remark #4

  • two 12V wall-outlet power supplies with 500 mA each (stabilized wide range switching power supplies with AC input range 100...240VAC, European type mains plugs)

  • cable and adapter board for connections between power supplies and bus board

  • building suggestion for wooden case (sketch + list of all required wooden case parts)

  • additional installation material like screws, nuts or distant bolts (e.g. for bus board, adapter board, rails) is not included as these parts depend upon the type of case built by the customer

  • Prices:

  • Euro 60.00 (complete kit incl. two power supplies)

  • Euro 50.00 (complete kit without power supplies)

  • attention: from Doepfer (Germany) only power supplies with European mains plug type are available (100...240V AC), please ask the Doepfer representative in your country if they have supplies available that are equipped with mains plugs for your country, stabilized supplies are required !

  • the technical document is available as pdf file

  • Remark # 1: This is an extremely inexpensive version of the power supply. The quality cannot be compared to those of the normal A-100 power supply (A-100PSU2). Stability of the voltages is significantly worse compared to the regular A-100 power supply (A-100PUS2). Especially if VCOs are are used tuning problems may occur. But the bus board and the mounting rails (these are the most expensive part of the kit) can be used later even in combination with a high quality supply (e.g. A-100PSU2 or A-100 DIY Kit 1). In case of doubt we recommend the A-100 DIY Kit 1 as the voltage stability of this kit is much better.

  • Remark # 2: As the thread distance is 2 HP only A-100 modules with two mounting holes can be mounted completely (i.e. all mounting screws). The threaded rails cannot be used for complete mounting of panels with 4 mounting holes as the distance between the holes is an odd HP multiple for these panels. We already asked our manufacturer to produce even rails with 1 HP thread distance and we hope that we will be able to offer these rails soon so that all types of panels can be mounted.

  • Remark # 3: If the version without power supplies is used: Because of electrical safety only encapsulated wall outlet power supplies are allowed (12V DC, stabilized, max. 500 mA, polarity: ring = GND, center = +12V). Open frame supplies that have to be wired to the mains by the user are not allowed ! This would nullify the safety advantages of the DIY kits. Even supplies with currents less than 500mA can be used provided that the total current of the modules is less than the max. current of the supplies.

  • Remark # 4: From about April/May 2008 the contents of the DIY kits will change to normal front rails (same as used in the standard A-100 frames and suitcases) instead of the mounting rails with threads mentioned above. To keep the costs as low as possible normal M3 nuts are slided into the rails (not threaded inserts as used in the standard A-100 frames and suitcases).